Drop Forged Wire Rope Clamps

DROP FORGED WIRE ROPE CLAMPS – Forged steel, hot galvanized
SIZE IN INCHES	MIN. CLAMPS  REQD.	TORQUE IN LBS. FT.*	APPROX. WEIGHT IN POUNDS	DIMENSIONS
				A	B	C	D	E	F	G
1/8	2	4.5	.05	.19	.75	.44	.44	.38	.81	.94
3/16	2	7.5	.10	.25	.94	.56	.56	.50	.94	1.19
1/4	2	15	.18	.31	1.06	.56	.75	.63	1.19	1.50
5/16	2	30	.31	.38	1.44	.75	.88	.75	1.31	1.69
3/8	2	45	.46	.44	1.50	.75	1.00	.88	1.56	1.94
7/16	3	65	.73	.50	1.88	1.00	1.19	1.00	1.81	2.31
1/2	3	65	.73	.50	1.88	1.00	1.19	1.06	1.81	2.31
9/16	3	95	1.00	.56	2.38	1.25	1.31	1.13	2.06	2.50
5/8	3	95	1.00	.56	2.38	1.25	1.31	1.25	2.06	2.50
3/4	4	130	1.50	.63	2.75	1.38	1.50	1.38	2.31	2.75
7/8	4	225	2.7	.75	3.19	1.44	1.81	1.69	2.63	3.31
1	5	225	2.7	.75	3.63	1.75	1.88	1.75	2.63	3.47
1 1/8	6	225	3.1	.75	4.00	2.00	2.00	1.88	2.81	3.56
1 1/4	7	360	4.6	.88	4.38	2.25	2.31	2.06	3.25	4.06
1 3/8	7	360	5.2	.88	4.63	2.31	2.38	2.25	3.44	4.25
1 1/2	8	360	5.9	.88	4.94	2.38	2.63	2.50	3.50	4.38
1 3/4	8	590	9.8	1.13	5.88	2.75	3.06	2.88	3.75	5.25
2	8	750	13.75	1.25	6.50	3.00	3.31	3.38	4.44	5.81
2 1/4	8	750	15.7	1.25	7.13	3.31	3.88	3.81	4.50	6.31
2 1/2	9	750	17.9	1.25	7.75	3.38	4.13	4.25	4.50	6.44

Blue U-Bolts (Korea)
When using U-bolt clamps, extreme care must be exercised to make certain that they are attached correctly. The correct way to attach U-bolts is shown above; the "U" section is in contact with the ropes\’s "dead end" and is clear of the thimble. The "live end", carrying the load, is gripped by the saddle of the clamp. Also, the tightening and retightening of the nuts must be accomplished as required.

 * Based on clean, unlubricated threads.
Hot galvanized, according to Federal Specification FF-C-450D, Type 1, Class 1. Does not include 1/8" and 3/16".
Table above shows minimum torque required to reach maximum holding power.
Caution: Never use any wire rope clamp to directly connect two straight lengths of wire rope.
WARNING: Read important warnings and safety information.

View this Hardware Now at Elite Sales

 CAUTION: THIS MATERIAL DESIGNED FOR DECKLASHING PURPOSES ONLY. NEVER EXCEED THE WORKING LOAD LIMIT.
WARNING: Read important warnings and safety information.

View this Hardware Now at Elite Sales

CAUTION: Never use any wire rope clamp to directly connect two straight lengths of wire rope.
WARNING: Read important warnings and safety information.

View this Hardware Now at Elite Sales

Drop Forged Fist Grip Clamps

US TYPE DROP FORGED FIST GRIP CLAMPS
SIZE IN INCHES	DIMENSIONS									APPROX. WEIGHT IN POUNDS
	A	B	C	D	E	G	L	M	N
3/16 – 1/4	.25	1.25	.34	.94	.38	1.28	1.63	.69	1.47	23
5/16	.31	1.34	.44	1.06	.38	1.47	1.94	.69	1.56	28
3/8	.38	1.59	.50	1.06	.44	1.81	2.38	.75	1.88	40
7/16 – 1/2	.50	1.88	.56	1.25	.50	2.19	2.75	.88	2.19	62
9/16 – 5/8	.63	2.28	.69	1.50	.63	2.69	3.50	1.06	2.63	103
3/4	.75	2.69	.88	1.81	.75	2.94	3.75	1.25	3.06	175
7/8	.88	2.97	.97	2.13	.75	3.31	4.13	1.25	3.14	225
1	1.00	3.06	1.19	2.25	.75	3.72	4.63	1.25	3.53	300
1 1/8	1.13	3.44	1.28	2.38	.88	4.19	5.25	1.44	3.91	400
1 1/4	1.25	3.56	1.34	2.50	.88	4.25	5.25	1.44	4.03	400
1 3/8 – 1 1/2	1.50	4.13	1.56	3.00	1.00	5.56	7.00	1.63	4.66	700

Bolts are an integral part of the saddle. Nuts can be installed in such a way as to enable the operator to swing the wrench in a full arc for fast installation.

• According to Federal Specification FF-C-450, Type III, Class I.
• All sizes have forged steel saddles.
• Entire clamp is Galvanized to resist corrosive and rusting action.
• All clamps are individually bagged or tagged with proper application instructions and warning information.
• Assembled with standard heavy hex nuts.
  WARNING: Read important warnings and safety information.

View this Hardware Now at Elite Sales

Drop Forged Wire Rope Clamps

DROP FORGED WIRE ROPE CLAMPS – Forged steel, hot galvanized
SIZE IN INCHES	MIN. CLAMPS  REQD.	TORQUE IN LBS. FT.*	APPROX. WEIGHT IN POUNDS	DIMENSIONS
				A	B	C	D	E	F	G
1/8	2	4.5	.05	.19	.75	.44	.44	.38	.81	.94
3/16	2	7.5	.10	.25	.94	.56	.56	.50	.94	1.19
1/4	2	15	.18	.31	1.06	.56	.75	.63	1.19	1.50
5/16	2	30	.31	.38	1.44	.75	.88	.75	1.31	1.69
3/8	2	45	.46	.44	1.50	.75	1.00	.88	1.56	1.94
7/16	3	65	.73	.50	1.88	1.00	1.19	1.00	1.81	2.31
1/2	3	65	.73	.50	1.88	1.00	1.19	1.06	1.81	2.31
9/16	3	95	1.00	.56	2.38	1.25	1.31	1.13	2.06	2.50
5/8	3	95	1.00	.56	2.38	1.25	1.31	1.25	2.06	2.50
3/4	4	130	1.50	.63	2.75	1.38	1.50	1.38	2.31	2.75
7/8	4	225	2.7	.75	3.19	1.44	1.81	1.69	2.63	3.31
1	5	225	2.7	.75	3.63	1.75	1.88	1.75	2.63	3.47
1 1/8	6	225	3.1	.75	4.00	2.00	2.00	1.88	2.81	3.56
1 1/4	7	360	4.6	.88	4.38	2.25	2.31	2.06	3.25	4.06
1 3/8	7	360	5.2	.88	4.63	2.31	2.38	2.25	3.44	4.25
1 1/2	8	360	5.9	.88	4.94	2.38	2.63	2.50	3.50	4.38
1 3/4	8	590	9.8	1.13	5.88	2.75	3.06	2.88	3.75	5.25
2	8	750	13.75	1.25	6.50	3.00	3.31	3.38	4.44	5.81
2 1/4	8	750	15.7	1.25	7.13	3.31	3.88	3.81	4.50	6.31
2 1/2	9	750	17.9	1.25	7.75	3.38	4.13	4.25	4.50	6.44

When using U-bolt clamps, extreme care must be exercised to make certain that they are attached correctly. The correct way to attach U-bolts is shown above; the "U" section is in contact with the ropes\’s "dead end" and is clear of the thimble. The "live end", carrying the load, is gripped by the saddle of the clamp. Also, the tightening and retightening of the nuts must be accomplished as required.

 * Based on clean, unlubricated threads.
Hot galvanized, according to Federal Specification FF-C-450D, Type 1, Class 1. Does not include 1/8" and 3/16".
Table above shows minimum torque required to reach maximum holding power.
Caution: Never use any wire rope clamp to directly connect two straight lengths of wire rope.
WARNING: Read important warnings and safety information.

View this Hardware Now at Elite Sales